8 inch ford rear end identification.

Ford Rear Axle Assembly Identification - Page 04: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDM-E: Ford Pickup '63-'72 F-100: 3.25: 9 in: NL: 28-WDM-F: Ford Pickup '63-'72 F-100: 3.50: 9 in: NL: 28-WDM-H:Boat735. One way to get old bearings off is to use a cut off wheel and cut through them carefully without damaging the axle. Another way is to take them to a machine shop and have them pressed off. The new one's need to be pressed on so you may as well have a machine shop do it (or any place with a press).A few ways to tell a the difference between a Ford 9" rear end and a Ford 8" rear end. The main way to tell is the 3rd member is flat on top on a Ford 8 inc...1977 Ford Axle Codes: Below is a axle code chart from 1977: There's no question, the easiest way to identify the axle and gear ratio in your truck is from the door sticker. If you open the drivers door and look at the door jamb, you'll see a sticker like the one shown below: You'll see that the area labeled (F) is for the Axle Code.

Ford 8-inch rearend: good ol' spot repairChevy truck rear axle identification Ford 8.8-inch axle builder’s guideBasic id ford 9 inch, rear, 8 inch rear end,carrier, center section. Rear axle ford 1986 rod brakes 1994 disc 1993 had hot five mustangs scrounger guide svo some hotrodChevy rear axle identification Ford maverick 8" rear endThe ...Ford Rear Axle Assembly Identification - Page 01 - FORDification.com . Reactions: sheza65. Save Share. ... I should have a 3.00 rear end and according to the Ford specifications for 1967 a three speed manual with a 3.00 rear end would have to be a limited slip differential only. The only thing I can make is that the number they have doesn't ...

The 9-inch ring and pinion is front-loaded into the rear end housing. First, the pinion shaft housing is removed from the front of the housing by removing five bolts. The ring and pinion are then accessed, also from the front, by removing another 10 bolts. Some of the 9-inch truck differentials will have an exaggerated hump on the rear cover to ...

from Santa Cruz. In re-guards to the axle ends the ones on the 8 inch are what they call small bearing ends. The 9 inch Ford housing came both ways, big and little. It just comes down to what backing plates and brakes you want to use and also what bolt pattern wheel you want.GM 9.76" 12 Bolt Rear, 2014-On. GM 10.5" Rear. GM 11.5" Rear End. GM Dana 60. GM / Chevy - Differential Identification Shop by your differential. Please select a rear end that matches your vehicle below. General Motors has a wide range of front and rear ends! We carry everything from the 7.25" IFS front end parts, to the large 11.5" rear ...thor the deal is the f150 is available with 3 axles. strongest to weakest top to bottom. 9.75B. 9.75. 8.8. edit for clarity. the number refers to sizing, bigger is better. The code appears as a number or letter/number combination in the 'Axle' column of the label. If you look at the 'AXLE' section on the label above, you'll see that this Ranger has a 'F7' axle code. Using the chart below, we know that this axle is a 7.5-Inch axle with a 4.10 limited slip. Axle codes for Ranger, Bronco II, Explorer and Aerostar ...

The 8" and 9" share the same axle lengths, so a '66 with a 9" would be the same axle length. Save Share. Like. 6. 66Racer Discussion starter ... Ford Muscle Cars Tech Forum. 951.9K posts 72.6K members Since 2001 A forum community dedicated to Ford performance owners and enthusiasts. Come join the discussion about popular models such as the ...

Could be 28, could be 31. If the rear axle ID tag is still present (many are missing today), post the code from it. I can look up the code, then cross it to the Ford axleshaft part number, list its spline count. Tag located at approx. 5 o'clock under one of the bolts that retains the carrier (pumpkin) to the housing.

This Ford 8"/9" rear end Panhard bar is used to control the side-to-side movement of the rear axle underneath the chassis. This is necessary when using a parallel 4-bar or hairpin radius rod style rear suspension. The track bar is threaded on one end for length adjustment and is welded on the opposite end. This will require one end to be unbolted to allow for the length adjustment. The ...Ford Rear Axle Assembly Identification - Page 13: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: S406-B: Ford F250SD, F350SD Pickup '99: 3.73: 10.50: NL--S406-C: Excursion '00 Ford F250SD, F350SD Pickup '99-01:269 posts · Joined 2012. #5 · Jan 14, 2013. The tag info you posted would be from an 8" differential. The 2.79 indicated ratio is 8" only. 9" equivalent ratio would be 2.75 for 1967. Best, Al.The Ford 8.8 rear axle has been a staple of the Ford ... It was first produced in 1983 and has been a common axle used in place of the venerable Ford 9-inch axle assembly. 4WD applications have ...60-63 falcon - tiny six cylinder rear end, four lug. 63 v8 8" rear end five lug - collectable since it fits the 60-63 cars. desierable for v8 conversions. since you don't have to mess with moving the spring perches. 64 v8 five lug - don't know off hand but i bet they're 8". oh, and if it is a v8 the frame mounts and intermediate mounts that go ...Ford 8 Inch (8 Ford) - Front dropout with 8.0 ring gear. Uses 28 spline bolt-in axles. Ring Gear Diameter: 8.000Differential Case Bolts: 10Ring Gea. My Account: ... Yukon 1541H cut to fit rear axle shaft for early Ford 8" with 28 splines: 0 Review(s) Your Price: $281.89 YA F8-28-32.87 - Yukon 1541H cut to fit rear axle shaft for early Ford 8 ...Dana Differential Identification. The Bill of Material (BOM) number is used to identify Dana differentials. Traditional BOM's are six digits long and begin with the number 60 or 61 followed by 1 or 2 digits, such as 605561-1. Later-model BOM's may start off with the first three digits of 200 rather than 60 or 61, for example 200561-1.

The code appears as a number or letter/number combination in the 'Axle' column of the label. If you look at the 'AXLE' section on the label above, you'll see that this Ranger has a 'F7' axle code. Using the chart below, we know that this axle is a 7.5-Inch axle with a 4.10 limited slip. Axle codes for Ranger, Bronco II, Explorer and Aerostar ...Rear : Ford Fairlane : 1962 - 1967 : Rear : Ford Ranchero : 1964 - 1978 : Rear : Axle Images: Axle Details. The Ford 8" axle is a smaller version of the popular Ford 9 inch axle and features a drop out style carrier, 8" diameter ring gear, removable pinion support, and 28 spline axle shafts.Ford 8-inch rearend: good ol' spot repairChevy truck rear axle identification Ford 8.8-inch axle builder’s guideBasic id ford 9 inch, rear, 8 inch rear end,carrier, center section. Rear axle ford 1986 rod brakes 1994 disc 1993 had hot five mustangs scrounger guide svo some hotrodChevy rear axle identification Ford maverick 8" rear endThe ...8.8 rear end versus 9.75 size difference. ... if you take out the 9.75 I can see how the 8.8 would be lighter and cheaper but a 9 inch like Casey's running is the ticket for weight savings and strenght ... like the L rear covers they make for the 9.75, Axles. Alot of work, youre taking a part most ford racers disgard. Born on 02/22/01 #1175 of ...60-63 falcon - tiny six cylinder rear end, four lug. 63 v8 8" rear end five lug - collectable since it fits the 60-63 cars. desierable for v8 conversions. since you don't have to mess with moving the spring perches. 64 v8 five lug - don't know off hand but i bet they're 8". oh, and if it is a v8 the frame mounts and intermediate mounts that go ...Ford 9" : what year i have to locate parts?Ford 8.8 rear end width chart. Ford differential identification axle tag rear codes info front tags truck trucks identifying parts thanks9 inch rear end Ford truck 9" rear end disc brake conversion kitRatio gear differential rear inch gears ranger ford final semi chart truck tires wheels australia ...Weight: The Ford 8.8 rear end is lighter in weight than the 9-inch rear end. Strength: The Ford 8.8 rear end is known for its strength and durability. It can handle up to 400 horsepower and 400 lb-ft of torque. Availability: The Ford 8.8 rear end is widely available and can be found in many Ford vehicles such as the Mustang, Thunderbird, and ...

Ford 8" Inch Rearend 3.55 Ring and Pinion TIMKEN Master Install Excel Gear Pkg. Brand New. $330.76. ronsmachiningservice1 (29,400) 99.9%. Buy It Now. Free 3 day shipping. Sponsored. Ford 8" Inch Rearend 3.80 Ring and Pinion TIMKEN Master Install Elite Gear Pkg. Brand New.The 1957-1958 Ford Ranchero and Courier pickups were pioneering designs. See pictures and learn about the 1957-1958 Ford Ranchero and Courier. Advertisement The 1957-1958 Ford Ranc...

Component 1: Axle Ratio. The axle ratio is the numerical representation of the gear ratio, which expresses the number of revolutions the driveshaft makes for each revolution of the axle. It determines the vehicle’s torque, towing capacity, and fuel efficiency. Common axle ratios found in Ford vehicles include 3.31, 3.55, 3.73, and 4.10.1965-66 Mustang 8 inch rear end identification question. I'm doing a six cylinder conversion on a 1965 Mustang. The front end components and everything is done. I purchased a rear axle and third member from Melvin's Classic Ford Parts. I know that the rear end has a 2.80 gear ratio because I counted the ring gear teeth and the pinion gear teeth ...The Chevy’s rear axle code contains information on the vehicle’s gear ratio, date of manufacture and the rear axle assembly plant. The prefix on the code consists of two letters fo...5981 posts · Joined 2007. #17 · May 10, 2010. The 8.8 didn't come out tell the mid 80s and the rear cover has bolts on it like every other rear end out there.The easiest way to tell a 8 inch from a 9 inch is try putting a socket on the lowest bolt on the 3rd member.A 8 inch the socket will go on a 9 inch it won't. Like.mustangboy. 6653 posts · Joined 2002. #2 · Feb 2, 2002. No the 8 and 8.8 rears are not the same.The 8inch is basically just a slightly smaller version of the 9 inch. The 8 and 9 inch rears have removable "pots" that go into the front of the axle housing as a complete assembly.The 7.5 and 8.8 rears used in the newer Fords have a cover that ...A fuel crisis in 1973 would further cement the death of the 9 3/8″ axle later in the decade. The 9 3/8″ rear end had an interesting and largely unknown 11-year run from 1966-1977, especially compared to the standard 9-inch, which Ford produced from 1957 through the 1986 model year. By 1977, the 9 3/8″ rear axle had outlived its usefulness.This helpful guide has images for easy identification. We also have printable version available. ... * 1310 Ford & 1330 Ford have 1 1/8" cap at pinion yoke and 1 1/16" cap at driveshaft. ** 1415, 1485, 1555 only found on Chrysler and some GM vehicles with American Axle built driveshafts. ...

The 9-inch ring and pinion is front-loaded into the rear end housing. First, the pinion shaft housing is removed from the front of the housing by removing five bolts. The ring and pinion are then accessed, also from the front, by removing another 10 bolts. Some of the 9-inch truck differentials will have an exaggerated hump on the rear cover to ...

Ford Rear Axle Assembly Identification - Page 13. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.

The Mustang II utilizes two different style rear axles. The first axle is used on 4cyl and some 6cyl cars and is a 6 3/4" ring gear integral carrier axle. The second is used on some 6cyl and all 8cyl cars and is an 8" ring gear removable carrier axle. The two axles are easy to tell apart. Looking at the axle from the rear of the car, if the ...On todays episode of Explained, we go over Axle Seals and how you go about measuring and replacing them in the case of a leaking axle.To purchase Axle Seals,...BTW if that 8 inch rear has 3.40:1 gears they have probably been replaced as I dont think any 67/68 came with that ratio from the factory. Also I prefer not to use the term 'posi' (aka positraction) which is a gm term. Ford term is Traction Loc. Generic term for a 'locking' rear axle is 'limited slip'. Good luck PaulCode Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WEM-A: Bronco '66-'71: 4.11: 8 3/4 in: NL: 281947 and Older Ford Trucks; Bronco. 2021+ Bronco; 2021+ Bronco Sport; 1978 - 1996 Big Bronco; 1966 - 1977 Early Broncos; Bronco II; Ford Vans and other vehicles. 2014+ Transit; Transit Connect; 1968-Present E-Series Van/Cutaway/Chassis; Ranchero & 1961 - 1967 Econoline; Nite, Nascar & Other Limited Edition Ford Trucks; Performance, Engines ...Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDD-B: Ford Pass., Mercury '65: 3.00: 8 3/4 inTechnical 9" Ford Rear Identification. Discussion in 'The Hokey Ass Message Board' started by kwsullivan, Feb 10, 2021. Joined: Feb 10, 2021 ... Outside of obscure bragging rights knowing exactly what vehicle the rear end came out of is insignificant. Some Bubba factor at the spit and whittle club if it came out of something like a big block ...A fuel crisis in 1973 would further cement the death of the 9 3/8″ axle later in the decade. The 9 3/8″ rear end had an interesting and largely unknown 11-year run from 1966-1977, especially compared to the standard 9-inch, which Ford produced from 1957 through the 1986 model year. By 1977, the 9 3/8″ rear axle had outlived its usefulness.7.5" vs 8.8" Rear Ends. The cover shape difference between 7.5" and 8.8" is the quickest way to identify an 8.8" from a 7.5" rear end. The 8.8" rear end is flat on the top and the bottom as well as the left and right. It has a square design with four rounded corners and ten bolts. When measuring from the top left bolt to the ...Jun 9, 2003 · I picked up a new 66 body that used to be a 6 cyl. but some one has converted it to a 5 lug. I want to find out what rear end it is because I am putting in a 351 windsor into it. The other question I have is that the 1966 289 mustang coupe car I am selling is set up different in the rear end. The support bars for the rear end come almost all ...

Aug 7, 2016 ... The first job was to identify what I actually have. I know the car was not originally a V8, so the 5 bolt rear end came from something else. My ...A. adgdghr123 Discussion starter. 1426 posts · Joined 2002. #1 · Dec 16, 2004. What are the rear axle ratio codes for a '67? I ask because I was thinking of changing gears in the rear-end in my '68 (8" I believe), but it occurred to me today that at my local junkyard there is a '67 Galaxie with a 390. I'd imagine with a 390 it probably has a ...Currie believes its billet pinion support is more than 25 percent stronger than conventional and stock units. It will fit all 8-inch gear cases and is available in a polished (PN CE-4033P; list ...How to Measure Ford Rear End Axle Splines, Flange Width and Height Ford 8 Inch and 9 Inch Third Members - Identify 28 and 31 Spline Axles, Yoke Flange Width and Height Metro Auto Parts MarketInstagram:https://instagram. rice cakes in walmarti 88 mile marker mapwalmart photo lab coupon codeharry hines dallas texas Photo 8 - Sorry no picture but from 69 to 78 Ford made the WER axle (the ID tag shows this rear as an 8.7-inch) used in the big cars and some Granada's which looks like the 8.8". It had a 10 bolt cover, used C-clips to hold the axles (like the 8.8") but had adjusting nuts for the carrier bearings (like the 9") instead of shims which are used in ...The 8.7" was used in some '75-80 Granadas. It does have a removable rear cover. It is not related to the 8.8" or 7.5", is pretty much an orphan and performance gearsets don't exist for that differential. It's reliable enough but parts just aren't available. As Jeff suggested - check the axle code on your door tag. That will be a good place to ... bubble guppies fruit flymorgan wallen concert song list Ford first used the 8-inch banjo-type axle in 1962 as an alternative to the 9-inch for their smaller body styles and smaller V-8 engines. Many Ford nameplates equipped with a small-block V-8 or six-cylinder engine used the 8-inch as standard equipment up until 1980. Several of the V-6 equipped models also used the 8-inch as their original ...that equals a ~12.7 at sea level. i launch at 3200 rpms on a C4 with an 8 inch supporting 10 inch quick time pro's. ive hit a 1.89 60ft. and im running a C4, it was holding up until the bolts came off the 2nd/3rd gear servo and i ripped the band to shreds :: another 69 stang is running 12.6's(~12.3) on an 8 inch and a 302. land for sale greene county ohio The size of speakers in a Ford Ranger depends on the generation. The Ford Ranger was produced by Ford Motor Company from 1983 until 2011. The third generation, produced from 1993 t...The 9-inch ring and pinion is front-loaded into the rear end housing. First, the pinion shaft housing is removed from the front of the housing by removing five bolts. The ring and pinion are then accessed, also from the front, by removing another 10 bolts. Some of the 9-inch truck differentials will have an exaggerated hump on the rear cover to ...The code appears as a number or letter/number combination in the ‘Axle’ column of the label. If you look at the ‘AXLE’ section on the label above, you’ll see that this Ranger has a ‘F7’ axle code. Using the chart below, we know that this axle is a 7.5-Inch axle with a 4.10 limited slip. Axle codes for Ranger, Bronco II, Explorer ...